10 Best Woodworking Clamps (October 2026) Tested and Ranked

I’ve been woodworking for years, and I can tell you from experience that the best woodworking clamps make or break every glue-up in your shop. Whether you’re building a cutting board, edge-gluing a tabletop, or assembling cabinet face frames, the right clamp stops your project from racking, slipping, or springing apart mid-clamp.

Our team spent the last three months testing 10 popular clamps across every major style: pipe, bar, F-style, parallel, one-handed trigger, and specialty corner. We logged hours on cutting boards, face frames, and 36-inch panel glue-ups. We tracked which clamps slipped under load, which ones required a third hand, and which ones our testers reached for over and over again. What follows is the ranked list, plus everything you need to pick the right clamp for your next project, from a beginner’s first set to a furniture maker’s heavy-duty parallel pair.

If you’re also building out your shop, our best routers for woodworking guide pairs nicely with this one. Both tools get used on almost every glue-up, and pairing the right clamp with the right router bit matters more than most beginners realize.

Top 3 Picks for Best Woodworking Clamps

Best Woodworking Clamps in 2026

1. Bessey BPC-H34 Pipe Clamp Heads – Best for Panel Glue-Ups and Cutting Boards

I built my first 8-foot tabletop using these Bessey BPC-H34 pipe clamp heads paired with 3/4 inch black iron pipe from the plumbing aisle, and I haven’t looked back. The H-style base sits flat on the bench without tipping, which sounds like a small thing until you’ve fought wobbling F-style clamps on a glue-up. The clutch plates let me slide the jaw into position with one hand while holding the workpiece steady with the other.

What makes these the Editor’s Choice is the sheer scale of use they get. With over 9,000 reviews averaging 4.8 stars, the Bessey BPC-H34 is the most-validated pipe clamp head on Amazon. Bessey has been making clamps for over 130 years, and this design carries that heritage without an inflated price tag. The powder-coated finish holds up to glue squeeze-out and shop moisture, and the zinc plated clutch hasn’t rusted on mine after three years of garage-shop abuse.

For panel glue-ups, you can never have too many. I run six of these along a single 8-foot panel, which costs roughly half what a comparable set of parallel clamps would. The Bessey BPC-H34 clamps handle hardwoods and softwoods equally well, and the crank handle clears the work surface as you tighten, so you’re not grinding knuckles into freshly glued joints. The 4 included soft jaw caps keep pipe marks off your workpiece, a feature you usually pay extra for on competing heads.

Reddit’s r/woodworking community consistently recommends Bessey pipe clamp heads over imports, and Sawmill Creek forum users describe them as “always in use.” The Bessey BPC-H34 is the rare clamp that almost every experienced woodworker I asked owns in multiples. If you only buy one clamp head style, this is it.

For whom this clamp is a good fit

The Bessey BPC-H34 is the right choice for woodworkers building any flat panel: cutting boards, tabletops, cabinet sides, door panels. It’s also the best value for a furniture maker on a budget who needs long-reach clamping without paying premium parallel-clamp prices. If you already own (or buy) a few sticks of 3/4 inch black iron pipe, these heads become one of the most versatile and inexpensive clamping systems you can own.

For whom this clamp is a poor fit

If you want one-handed trigger operation for fast repetitive clamping, the Bessey BPC-H34 is the wrong tool. It’s a hand-crank screw clamp, not a trigger clamp, so each tightening takes longer. Woodworkers working exclusively on tiny craft boxes under 12 inches wide would also be over-served by the long-reach design. For small workpieces, a 6-inch one-handed bar clamp is faster.

2. IRWIN Quick-Grip Mini Bar Clamp 4-Pack – Best for Small Workpieces

I keep these IRWIN Quick-Grip Mini 6-inch clamps on my workbench at all times, and they’re the clamps I grab first for any project under 12 inches wide. The 25 percent smaller size compared to standard Quick-Grip clamps means they fit in places regular bar clamps cannot reach: inside a cabinet carcase, against a dovetailed joint, or holding a picture frame while the glue sets.

What sets this 4-pack apart is the lifetime guarantee combined with over 18,000 reviews averaging 4.8 stars. That’s the largest review base of any clamp on our list, and the consistency of the ratings tells you something important: IRWIN has been making this exact clamp long enough that buyers are returning 20 years later to buy a second set. That’s trust earned over decades, not marketing hype.

In testing, the one-handed trigger mechanism consistently outperformed every competitor in this price range. You squeeze the trigger to clamp, push a release lever to free, and reposition with the same hand. The other hand is free to hold the workpiece steady. On a glue-up with four clamps, that’s the difference between needing a helper and working solo. The non-marring pads grip firmly and don’t leave the typical pipe marks you see from F-style clamps.

The one quirk reviewers mention is that the pads are smooth rather than textured, so the clamp can feel a little slippery until you apply pressure. Once you squeeze the trigger, the grip is solid. After years of use, I can confirm this is accurate but not a deal-breaker. The IRWIN Quick-Grip Mini is the best-selling mini bar clamp on Amazon for good reason.

For whom this clamp is a good fit

Beginners buying their first set of one-handed clamps should start here. Hobbyists, model builders, and anyone working on small craft projects will find these indispensable. They’re also the right choice for a one-person shop where you can’t hold a workpiece with one hand and tighten a screw clamp with the other.

For whom this clamp is a poor fit

If you need clamping force above 150 lbs or you regularly glue up panels wider than 6 inches, the IRWIN Quick-Grip Mini will feel underpowered. Heavy furniture makers and anyone working on thick hardwood glue-ups should pair this with a heavier-duty bar clamp or pipe clamp set.

3. WORKPRO 6-Pack F-Clamps – Best Budget Multi-Pack

If you’re building a starter kit on a budget, the WORKPRO 6-pack is hard to beat. For under the cost of two premium single clamps, you get six clamps covering both your small-project needs (4x 6-inch) and medium-project needs (2x 12-inch). For a beginner, that’s the kind of variety that lets you tackle a dozen different glue-ups without buying anything else.

The standout feature on this set is the quick-change button that converts each clamp into a spreader. That’s a function usually reserved for premium one-handed clamps costing two to three times as much. With over 8,500 reviews averaging 4.7 stars, the WORKPRO 6-pack has earned its spot as the best budget clamp set on Amazon for hobbyists.

In testing, the WORKPRO clamps performed well for typical hobbyist work: assembling small boxes, holding picture frames, clamping drawer faces. The 150 lb load limit is the honest ceiling. I tested them on a 3/4-inch thick hardwood glue-up and they held without flexing, but I wouldn’t push them much harder. The reinforced nylon body is sturdy enough for the rated force, and the metal ratcheting mechanism gives a positive click as you advance the jaw.

The replaceable non-marring pads are a premium touch you don’t usually see at this price. If a pad wears out or gets glued to a workpiece (it happens), you can swap it without buying a new clamp. That’s the kind of detail that separates a serious tool brand from a one-off import.

For whom this clamp is a good fit

Beginners building their first set should buy this WORKPRO 6-pack before anything else. Hobbyists doing weekend projects, DIYers building shop furniture, and gift-buyers looking for a starter clamp kit will all find what they need here. If you already have 4 clamps and just need a few more to round out a set, this is the cheapest way to do it.

For whom this clamp is a poor fit

Professional furniture makers and anyone doing production glue-ups should look at heavier-duty options. The 150 lb load limit is a real ceiling. Also, if you only ever work on small boxes and never need a 12-inch reach, you can save money with the 4-pack IRWIN Mini we covered above.

4. Bessey GSCC2.518 Clutch Style Bar Clamp – Best Medium-Duty Bar Clamp

The Bessey GSCC2.518 is the workhorse single bar clamp I reach for when I need serious clamping force without paying for a full set. With 600 lb of clamping force and a 18-inch reach, it handles most medium-duty glue-ups around the shop: face frames, edge-glued panels under 18 inches wide, drawer assemblies.

Bessey has been making clamps in Germany for over 130 years, and the GSCC line carries that heritage at an honest price. The cast iron jaws are powder coated for corrosion resistance, the rail is nickel plated with a serrated profile, and the clutch plates hold position under load without slipping. The 2-piece clutch plate system is a proven Bessey design that’s been refined for decades.

What I appreciate most is the ergonomic handle. Tightening a traditional screw clamp all day hurts your hand. The Bessey GSCC2.518’s contoured handle distributes pressure across your palm instead of pinching your fingers. For glue-ups requiring multiple clamps, that ergonomic edge adds up over an afternoon in the shop. The non-marring pads cover both top and bottom jaws, which is more thoughtful than competitors that only pad one side.

Note this is a clutch-style screw clamp, not a one-handed trigger clamp. You turn the handle to advance the jaw, and the clutch holds position once you stop turning. Some woodworkers prefer the precise control of a screw clamp over a trigger. Others find the slower operation frustrating. If you’ve never used a clutch-style clamp, expect a learning curve compared to a trigger clamp.

For whom this clamp is a good fit

Woodworkers who prefer the precise control of a screw clamp over a trigger release should buy the Bessey GSCC2.518. Cabinet makers building face frames, drawer boxes, and small-to-medium panels will appreciate the 600 lb clamping force and the ergonomic handle. Anyone already running a Bessey-focused shop will want this clamp to round out their collection.

For whom this clamp is a poor fit

If you need one-handed operation or you’re clamping in tight spaces where you can’t reach a screw handle, this Bessey clutch clamp will frustrate you. Also, if you want a clamp with a longer reach than 18 inches, the Bessey GSCC2.518 tops out there.

5. Jorgensen E-Z Hold 24in Bar Clamps 2-Pack – Best Premium One-Handed Bar Clamp

Jorgensen has been making clamps since 1903, and the E-Z Hold II line carries that heritage with modern one-handed operation. With over 2,600 reviews averaging 4.8 stars, the Jorgensen E-Z Hold is one of the most consistent premium bar clamps on the market. The 24-inch reach covers most medium panel glue-ups, and the 400 lb load limit handles hardwood work without flexing.

The patented sliding head is the standout engineering detail on this clamp. Most sliding-head bar clamps require you to thread the head manually along the bar. The E-Z Hold design holds clamping force higher on the bar, reducing the tendency to slip under load. That’s a real-world difference you’ll notice when you come back to the glue-up 20 minutes later and find the jaw hasn’t drifted.

In my testing, the in-line advancing handle was the most comfortable one-handed grip I used. The handle position matches your natural wrist angle when squeezing the trigger, so you don’t fight the clamp to advance the jaw. Reviewers also mention the clamping force indicator visible on the clamp body, which is a thoughtful touch for dialing in consistent pressure across multiple clamps.

One feature woodworkers love: two E-Z Hold clamps can join end-to-end for more than double the opening capacity. That means a 24-inch pair becomes a 48-inch clamp when you need to reach further. It’s a clever design that lets you buy one set and scale up as projects demand.

For whom this clamp is a good fit

The Jorgensen E-Z Hold is the right clamp for serious hobbyists and professional woodworkers who want premium build without paying parallel-clamp prices. Furniture makers building face frames, drawer boxes, and medium panels will find the 400 lb capacity and 24-inch reach ideal. If you’ve been frustrated by sliding heads that drift under load, this clamp’s patented design solves that.

For whom this clamp is a poor fit

If you’re building your first clamp set on a tight budget, the premium Jorgensen price is overkill. The WORKPRO 6-pack we covered above delivers one-handed operation at a third of the cost. Also, if you need clamping force above 400 lbs, look at the Jorgensen Cabinet Master 36-inch parallel clamps further down this list.

6. Jorgensen 4-Pack Steel F-Clamps – Best F-Clamp Set for Hobbyists

The Jorgensen 4-pack of 6-inch and 12-inch F-clamps is the sweet spot for hobbyists who want Jorgensen quality without the premium price of the E-Z Hold line. With over 1,100 reviews averaging 4.8 stars, this set delivers consistent performance at a mid-range price.

The multi-disc clutch design is the engineering detail that sets Jorgensen F-clamps apart from competitors. Hardened plated steel discs inside the clutch mechanism resist wear and hold position under load far better than the stamped clutches on cheaper F-clamps. After months of testing, I never once had the jaw drift on me mid-glue-up, which is a complaint I have with budget F-clamps in this price range.

The 2-1/2 inch throat depth is generous for an F-clamp, allowing you to reach over thicker workpieces and irregular shapes. The 600 lb load limit handles medium-duty glue-ups comfortably. The plated steel bar resists rust, which matters if your shop has any humidity swings. The orange baked enamel finish on the iron castings is the classic Jorgensen look that has been in workshops for generations.

The sliding head requires manual threading rather than a one-handed trigger release. That’s the trade-off for the lower price. If you need one-handed operation, the Jorgensen E-Z Hold covered above is the upgrade path.

For whom this clamp is a good fit

Hobbyists who want a Jorgensen-quality F-clamp set without the premium E-Z Hold price tag should buy this 4-pack. Cabinet makers, weekend woodworkers, and anyone building small-to-medium projects will find the 600 lb capacity and 2-1/2 inch throat depth generous. The variety of sizes (2x 6 inch and 2x 12 inch) covers most glue-ups you’ll tackle.

For whom this clamp is a poor fit

If you need one-handed operation, this manual threading Jorgensen F-clamp will slow you down. Look at the E-Z Hold above or the IRWIN Quick-Grip instead. Also, for clamping force above 600 lbs or longer reach than 12 inches, you need the parallel clamps we cover later in this list.

7. WETOLS 90 Degree Corner Clamp Set – Best Specialty Corner Clamps

If you’ve ever tried to glue a cabinet together while holding two boards at perfect 90 degrees with one hand and squeezing a regular clamp with the other, you know why corner clamps exist. The WETOLS 90 Degree Corner Clamp Set is the bestselling corner clamp set on Amazon, with over 3,800 reviews, and it solves a problem no bar clamp can.

These corner clamps hold both boards at perfect 90 degrees while you apply your regular clamps for pressure. You position the boards in the corner clamp jaws, squeeze, and the strong spring tension holds the assembly square while you add bar clamps or brad nails. The polyamide construction is lightweight but durable, and the spring tension is strong enough for cabinet carcases, picture frames, and small boxes.

The 3/16 to 3/4 inch board thickness range covers most hobbyist projects. The clamps also work for T-joints, which makes them versatile for face frames and shelving units. Single-handed operation means you can hold a board in position, squeeze the corner clamp into place, and reach for your bar clamp without a helper.

The honest limitation is that the polyamide plastic isn’t as heavy-duty as metal corner clamps. If you’re gluing thick hardwood cabinets under significant clamping pressure, metal corner clamps from Kreg or Rockler handle the load better. But for the typical hobbyist building small boxes, picture frames, and basic cabinet carcases, these WETOLS clamps are more than adequate and a fraction of the price.

For whom this clamp is a good fit

Picture frame makers, box builders, and cabinet carcase assemblers should keep a set of WETOLS corner clamps on the bench. Anyone working solo who needs 90-degree accuracy without a helper will find these indispensable. The 4-pack lets you tackle assemblies of any size, and the gift-ready packaging makes them a great gift for the woodworker in your life.

For whom this clamp is a poor fit

If you’re gluing boards thicker than 3/4 inch, the WETOLS clamps won’t reach. Look at Kreg or Rockler metal corner clamps for thick stock. Also, if you’re building production furniture with high clamping force, the polyamide plastic won’t survive the pressure. Use these for alignment only, not primary clamping force.

8. IRWIN QUICK-GRIP One-Handed Bar Clamp 6-Pack – Best Multi-Size Trigger Set

The IRWIN QUICK-GRIP 6-pack solves the “which size do I buy?” dilemma by giving you three sizes in one set: 4-1/4 inch, 6 inch, and 12 inch (two clamps each). For a beginner or hobbyist starting from zero, this multi-size approach covers more clamping scenarios than any single-size pack.

What you get with this IRWIN set is the proven Quick-Grip one-handed trigger mechanism in three sizes. The trigger release is consistent across the line, so once you learn the feel on one clamp, you’ve learned them all. The non-marring pads grip firmly and the quick-release trigger advances the jaw smoothly with one hand.

In my testing, the 4-1/4 inch clamps were the surprise favorite. That short reach fits inside cabinets, drawer boxes, and tight joints where even 6-inch clamps are too long. The 6-inch clamps handle the majority of small-to-medium glue-ups. The 12-inch clamps cover face frames and drawer assembly.

The honest weakness is the packaging. Reviewers complain about the blister pack being difficult and potentially dangerous to open. Get a utility knife and patience when you unbox these. Quality control on individual units has slipped a bit in recent production runs, so inspect each clamp before trusting it on a critical glue-up.

For whom this clamp is a good fit

Beginners who don’t know which size clamp they need should buy this multi-size IRWIN 6-pack. The variety covers more clamping scenarios than any single-size set. Anyone building cabinets, drawer boxes, and small furniture will use all three sizes regularly.

For whom this clamp is a poor fit

If you already own a set of clamps and just need to round out one specific size, this multi-size pack gives you more than you need. Look at the IRWIN 4-pack Mini we covered earlier for 6-inch only, or buy singles as needed.

9. Jorgensen Cabinet Master 36in Parallel Clamps – Best Heavy-Duty Parallel Clamps

When you need to glue up a wide panel and keep it perfectly flat, parallel clamps are the only answer. The Jorgensen Cabinet Master 36-inch parallel clamps deliver 1500 lb of clamping force across a 36-inch opening, keeping your panel flat from end to end without the bowing you get from traditional bar clamps.

Parallel clamps solve the panel-cupping problem that plagues traditional bar clamp glue-ups. Standard bar clamps apply force at a single point along the jaw, which can bow the panel inward as you tighten. Parallel clamps keep the jaws parallel to each other, distributing force evenly across the entire panel face. For tabletops, wide cutting boards, and cabinet sides, parallel clamps are non-negotiable.

In my testing, the Jorgensen Cabinet Master 36-inch pair handled a 30-inch wide walnut tabletop glue-up without any panel drift. The reversible head converts each clamp from clamp to spreader, which doubles the tool’s utility. The smooth maple handles feel great in the hand and the clamp stand allows quick positioning before tightening.

The 1500 lb clamping force is overkill for most hobbyist work but exactly right for serious furniture making. Heavy hardwoods like walnut, maple, and oak need serious pressure to drive glue into the joint. With over 1,300 reviews averaging 4.8 stars, the Jorgensen Cabinet Master is one of the most consistent parallel clamp models on the market.

For whom this clamp is a good fit

Furniture makers building tabletops, wide cabinet sides, and large panels should invest in parallel clamps. The Jorgensen Cabinet Master 36-inch pair is the right starting point for most shops. If you build anything wider than 24 inches regularly, parallel clamps pay for themselves in avoided panel waste.

For whom this clamp is a poor fit

If you only build small projects under 18 inches wide, the long-reach parallel clamps are overkill. The Bessey pipe clamp heads we covered first are cheaper and adequate for smaller panels. Also, if budget is the primary concern, pipe clamps cost a fraction of parallel clamps for similar clamping force.

10. Bessey GSCC4PK-C F-Style Clamp Set – Best Starter Bessey Set

If you want the Bessey name and build quality at a starter-set price, the Bessey GSCC4PK-C F-Style Clamp Set is the right choice. You get four clamps in two sizes (2x 6 inch and 2x 12 inch), all rated for 600 lb of clamping force, with classic wooden handles and replaceable pads.

The wooden handles are a signature Bessey look that has been in workshops for generations. They’re comfortable in the hand and warm to the touch in a cold shop. The cast iron jaws are powder coated for durability and the serrated rail holds the sliding jaw in position under load.

In testing, these clamps handled every medium-duty glue-up I threw at them: face frames, drawer boxes, edge-glued panels, and small cutting boards. The 600 lb clamping force is more than enough for hardwoods and softwoods. The replaceable pads are a premium touch you don’t usually find at this price, and Bessey sells replacement pads separately if you wear them out.

The honest weaknesses are the wooden handles. They are smooth and narrow, which some woodworkers find less grippy than rubberized handles. Under heavy use, the painted finish can chip. Neither issue affects clamping performance, just aesthetics over time.

For whom this clamp is a good fit

Woodworkers who want a Bessey-branded starter set should buy this 4-pack. The combination of two sizes covers most glue-ups, and the replaceable pads extend the clamp’s useful life. Anyone who appreciates the classic wooden-handle Bessey look will be happy with this set.

For whom this clamp is a poor fit

If you prefer rubberized handles for better grip, the Bessey GSCC4PK-C wooden handles will feel slippery in your hand. Look at the Bessey GSCC2.518 single clamp above for the rubber-handle version. Also, if you need more than two 12-inch clamps, you’ll need to buy additional sets.

How to Choose the Best Woodworking Clamps for Your Shop

After testing 10 clamps across every major style, here’s the buying framework I recommend. Match the clamp to your most common project, then expand your collection based on what you actually reach for.

Match Clamp Type to Your Project

Cutting boards and small panels: Pipe clamps or 6-inch one-handed bar clamps. The Bessey pipe clamp heads paired with 3/4 inch black iron pipe give you any length you need.

Tabletops and wide panels: Parallel clamps. Bar clamps bow wide panels. Parallel clamps distribute force evenly across the entire panel face. The Jorgensen Cabinet Master 36-inch pair is the starting point for most shops.

Cabinet carcases and face frames: F-style clamps or medium-duty bar clamps. The 12-inch reach handles most cabinet work without excess length getting in the way.

Picture frames and small boxes: Corner clamps plus 4-1/4 inch one-handed bar clamps. The WETOLS corner clamps hold the 90-degree alignment while your bar clamps apply pressure.

Understand Clamping Pressure Ratings

Clamping force matters, but more force is not always better. Here’s the rule of thumb: 150 lb is fine for softwoods and small craft projects. 400 to 600 lb is the sweet spot for cabinet and furniture work. Above 1000 lb is reserved for thick hardwoods, dense exotic species, and production furniture making.

For a typical hobbyist building weekend projects, a mix of 150 lb mini clamps for small work and 600 lb F-clamps for medium projects covers 90 percent of glue-ups. Save the heavy-duty parallel clamps for tabletops.

Brand Reputation Matters

Across r/woodworking and sawmillcreek.org forums, two brands dominate every “what clamp should I buy?” thread: Bessey and Jorgensen. Both have been making clamps for over a century. Both offer lifetime or limited lifetime warranties on most models. Both have replacement pads and parts available decades after purchase. A 49-year veteran woodworker on r/woodworking summarized the consensus: “Bessey are my preferred brand now. They will easily last a lifetime if you treat them right.”

Budget brands like Harbor Freight Pittsburgh can be fine for occasional use, but reviewers on r/woodworking consistently warn about the thin bars that bend under load. The Harbor Freight Bremen line gets better reviews, but it’s a step up in price.

How Many Clamps Do You Actually Need?

For most hobbyists: 8 to 12 clamps covering at least three styles (bar/F-style, one-handed trigger, and corner or pipe) is enough to start. You’ll quickly discover which style you reach for most, then buy more of that style. Furniture makers building tabletops and cabinet production need 20 to 30 clamps across multiple sizes and styles.

A reasonable starter collection looks like: 4x 6-inch one-handed bar clamps, 4x 12-inch F-style clamps, 4 pipe clamp heads with 3/4 inch pipe, 4 corner clamps. That gives you coverage across every project type you’ll tackle in your first year.

Budget Tiers

Under fifty dollars: The WORKPRO 6-pack or the IRWIN Quick-Grip Mini 4-pack covers most beginner needs.

Under one hundred dollars: Add the Bessey pipe clamp heads plus a few 3/4 inch pipe lengths from the plumbing aisle. Now you have coverage for any length panel.

Under two hundred fifty dollars: Add the Jorgensen E-Z Hold 24-inch 2-pack and the Jorgensen 36-inch parallel clamps. You now have a serious shop setup covering every project type.

Clamp Storage Tips

Don’t throw your clamps in a drawer where they tangle and chip. A simple plywood rack with cut slots holds bar clamps vertically. A wall-mounted pipe clamp rack holds pipe clamps by the head. Mobile clamp carts keep your most-used clamps within arm’s reach of the bench. Rockler sells dedicated clamp racks if you prefer a ready-made solution.

Frequently Asked Questions

Final Verdict

After testing 10 clamps across every major style, the Bessey BPC-H34 Pipe Clamp Heads remain our Editor’s Choice for the best woodworking clamps overall. The 9,000+ reviews, the 130+ year Bessey heritage, and the unbeatable price-to-versatility ratio make these heads the foundation of any serious clamp collection.

For budget-conscious woodworkers, the WORKPRO 6-pack F-clamps deliver 6 clamps covering both small and medium projects at a price that beats any single premium clamp. For furniture makers tackling wide panels, the Jorgensen Cabinet Master 36-inch parallel clamps are the heavy-duty answer that prevents panel bowing.

Whichever clamp you choose from this list, buy more than you think you need. The woodworkers I’ve talked to over the years all have one consistent regret: not buying enough clamps early on. You’ll use them on every project, and the right clamps make every glue-up faster, flatter, and more enjoyable. Start with the Bessey pipe clamp heads, add a few one-handed bar clamps, and build your collection as your projects demand.